1965-1973 Mustang Shelby GT500 Coil Spring Compressor Free Thrust Bearing!!

• Popularity - 20285 views, 2897.9 views per day, 7 days on eBay. Super high amount of views. 256 sold.
• Price - Avg: $0.00, Low: $0.00, High: $0.00. Best quality when compared to PicClick similar items.
• Seller - + items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.

THIS TOOL DOES NOT COME PAINTED!! I DO NOT HAVE THE EPA REQUIRED PAINT FACILITIES TO PAINT THIS. I suggest lightly oiling the tool since it is going to get scratched during use.<br>-The Tommyzees coil spring compressor, the name that stands for quality.<br>-My only job is vintage Mustangs and Fords, I am not a Johnny Come Lately Ebay seller who copied some one else's product. I will be here to answer any tech question regarding the use of this spring compressor for years to come.<br>-The original.<br>-Made in the USA!!<br>-Thousands sold in 30 years.<br>-Often imitated, never duplicated.<br>-The original, don't settle for cheap imitations.<br>-3/8" thick x 3 1/2" x 1 1/2" heavy duty top plate to spread the load out. A 1/8" thick SAE hardened washer is welded on top of the plate to prevent wear. (DO NOT SETTLE FOR A CHEAP 1/4' THICK TOP PLATE!!)<br>-Super heavy duty design, this is the last spring compressor you will buy.<br>-Do not settle for an un-safe design.<br>-3/4" Acme threaded rod.<br>-Free Thrust Bearing-<br>Here is a real problem solver when you are trying to do front suspension work: This is a front coil spring compressor used to remove and install front coil springs in '64-'70 Mustangs, and '69-'77 Mavericks and their Mercury counterpart Comets.  WILL NOT WORK ON '62-'65 Fairlanes.  It is made out of heavy gauge steel .120" WALL SQUARE TUBING. Pipe is not a structural material and should not be used for something this critical. This is MIG welded personally by myself, a certified welder. It works by lowering the tool through the hole on top of the shock tower, the lower part of the tool is attached to the lower spring saddle, and the upper shock tower mount is bolted back on to the shock tower. The flat plate is bolted to the shock mount, and the washer and nut are threaded on to the tool. The nut is turned clockwise to compress the spring about 3". With the spring compressed, the spring saddle is un-bolted from the upper control arm and the upper control arm is unbolted from the shock tower. The nut is then turned counter clockwise to release the tension on the spring. Installation is the opposite of the above. I personally build and weld each and every one of these compressors in my fabrication shop, and I have been building them for at least 30 years and I have sold thousands to satisfied customers. This is a very safe and in-expensive compressor to use.<br>Detailed instructions are included.<br>See my other auctions for my roller bearing front coil spring perches for shock tower equipped Fords including Mustang,Falcon,Comet,Ranchero and Cougar.<br>Spring Compressor Instructions<br>·<br>PLEASE READ AND UNDERSTAND THE INSTRUCTIONS COMPLETLY BEFORE STARTING TO USE THIS TOOL.<br>·<br>THIS TOOL WILL<br>NOT<br>WORK ON '62-'65 FAIRLANES.<br>·<br>USE TOOL AT YOUR OWN RISK. IF THE INSTRUCTIONS ARE FOLLOWED, THIS IS A VERY SAFE SPRING COMPRESSION TO USE.<br>·<br>You can refer to the Ebay auction where this tool was purchased for a set of instructions with pictures.<br>·<br>Please lubricate the threaded rod and nut with WHITE LITHIUM GREASE, NOT WD-40!!!<br>·<br>The flat plate is for Mustang and Cougar applications only.<br>·<br>One stud on the tool is slightly longer than the other to aid in reaching the spring perch holes if the perch is at an angle.<br>·<br>The flat plate is drilled for early (’64-’66) and late (’67-’70) Mustang bolt patterns, it is not mis-drilled.<br>·<br>YOUR UPPER SHOCK MOUNT HAS TO BE USED IN CONJUNCTION WITH THIS TOOL. THE SHOCK MOUNT HAS TO BOLT BACK ON TOP OF THE SHOCK TOWER. DO<br>NOT<br>TRY TO USE THIS TOOL WITHOUT THE SHOCK MOUNT IN PLACE.<br>1. After safely supporting the vehicle on jackstands, remove the front shocks.<br>2.<br>Slide spring compressor down through the shock tower (threaded rod portion up) and attach it to the lower spring seat just as you would the lower part of the shock.  Install the flat washers on the studs before the nuts, so they will not pull through the spring seat. You can now re-install the stock upper shock mount and bolt it to the shock tower using the original hardware.<br>3.<br>If you are working on a vehicle that uses a stud on the upper portion of the shock, you can omit this next step and